Superior DRL6072 72" Linear Contemporary Direct Vent Gas Fireplace
The Superior DRL6072 is a 72" linear direct vent gas fireplace from the DRL6000 series, which comes with a factory-installed blower, floor lighting, a black porcelain liner and a multi-function remote. The ceramic glass viewing area is 68-5/8" wide and 15-5/8" tall, and the burner runs from 45,000 down to 31,500 Btu/hr on natural gas over six flame settings.
It ships for natural gas (DRL6072TEN); Superior's conversion kit changes it to propane (43,000 to 32,250 Btu/hr). It is a sealed-combustion unit that vents through 6" x 9" Superior 6DVL (DV Lock) pipe, and the electronic IPI/CPI ignition has a four AA battery backup, so the burner still lights in a power outage; the blower and lights wait for power to come back. Non-combustible fireboard ships in the box to finish the face, and a see-through kit can turn it into a two-sided fireplace.
If you don't need the blower, lights and remote, the Superior DRL4072 is the same 72" size and framing without them. The DRL6000 series also comes in 48" (DRL6048), 60" (DRL6060) and 84" (DRL6084).
Play video: Superior DRL6000 Direct Vent Gas Fireplace
Key Features
- 68-5/8" x 15-5/8" ceramic glass viewing area on an 86" wide fireplace
- Natural gas: 45,000 to 31,500 Btu/hr; propane with the conversion kit: 43,000 to 32,250 Btu/hr
- Six flame height settings
- Factory-installed blower with six speed settings
- Floor lighting with six settings that works with or without the fire on
- Multi-function remote included: on/off, thermostat mode, flame height, blower and lights
- Black porcelain liner and platinum crushed glass media standard
- Electronic IPI/CPI ignition with a four AA battery backup that runs the burner in a power outage
- Clean face with integrated tile stops and 1/2" non-combustible fireboard included
- See-through conversion kit available
- Optional HeatFlo kit sends heat out a register above the fireplace by natural convection, with no blower or electricity, to keep the wall cooler for a TV or artwork
- Optional power vent kit for down-and-out venting
- Vents with 6" x 9" Superior 6DVL (DV Lock) direct vent pipe, up to 40 ft vertical
- Listed for bedrooms, aftermarket mobile homes and manufactured homes
- 20 year limited warranty on the body, firebox and barrier, and on the ceramic glass against thermal breakage
What's Included
- Electronic IPI/CPI ignition with battery backup
- Platinum crushed glass media (four 5 lb bags)
- Ceramic glass front with protective screen barrier
- Black porcelain liner
- Factory-installed six-speed blower
- Floor lighting
- Multi-function hand-held remote control
- Four AA batteries for the battery backup and three AAA batteries for the remote
- 1/2" non-combustible fireboard (top, bottom and two sides) with screws
- Top standoff assembly and heat shield
What to Order With It
Required – Venting (6" x 9" 6DVL, ordered separately):
Optional – See-through and HeatFlo kits:
Optional – Trim and liner:
Optional – Media and logs:
Optional – Power vent:
Optional – Gas conversion and touch-up:
Specifications
| Model |
DRL6072TEN (natural gas; propane with conversion kit) |
| Order number |
F4391 |
| Type |
Linear direct vent gas fireplace, single-sided (see-through with kit), sealed combustion |
| Input, natural gas |
45,000 Btu/hr high, 31,500 Btu/hr low |
| Input, propane (conversion kit) |
43,000 Btu/hr high, 32,250 Btu/hr low |
| Efficiency, natural gas |
55.0% AFUE, 57.0% P4 |
| Efficiency, propane |
55.0% AFUE, 57.8% P4 |
| Glass viewing area |
68-5/8" W x 15-5/8" H |
| Fireplace size |
86" W x 48-1/4" H x 20-1/8" D |
| Framed opening |
86-1/4" W x 48-1/2" H x 19-1/2" D (18-1/2" D see-through) |
| Ignition |
Electronic IPI/CPI with four AA battery backup |
| Blower |
Factory-installed, six speeds |
| Lighting |
Floor lighting, six settings |
| Remote |
Multi-function hand-held remote: on/off, thermostat, six flame heights, blower and lights |
| Power |
120 VAC, 60 Hz, unswitched, grounded, to the junction box on the left side |
| Gas inlet pressure |
Natural gas 5" to 10.5" WC; propane 11" to 13" WC |
| Venting |
Direct vent, top, 6" x 9" Superior 6DVL (DV Lock); power vent kit optional |
| Vent run |
Up to 40 ft vertical, starting with at least 2 ft of vertical vent off the fireplace; horizontal run and restrictor setting per the vent chart in the manual |
| Glass and barrier |
Ceramic glass with protective screen barrier |
| Media and interior |
Platinum crushed glass (four 5 lb bags); black porcelain liner |
| Altitude |
0 to 4,500 ft with the standard orifices |
| Listing |
ANSI Z21.88 / CSA 2.33 and CSA 2.17, vented gas fireplace heater (PFS report F11-26) |
| Approved locations |
Bedrooms; aftermarket mobile homes and permanently located manufactured homes (USA only) |
| Shipping weight |
575 lb |
| Warranty |
20 year limited (see Warranty below) |
Efficiency figures are from Superior's installation manual, Table 10; the propane figures are with the conversion kit installed. AFUE is the US Department of Energy measure; P4 is the Canadian CSA P.4.1 fireplace efficiency rating.
Dimensions and Framing
Fireplace dimensions
| Overall width (A) |
86" |
| Vent center from the left side (B) |
43" |
| Glass viewing width (C) |
68-5/8" |
| Body width at the front (D) |
73-1/2" |
| Width across the side flanges (E) |
88-5/8" |
| Glass viewing height |
15-5/8" |
| Fireplace opening height |
21" |
| Base to bottom of the opening |
9-1/2" |
| Height to top of the firebox |
37-1/2" |
| Height to top of the vent collar |
40-3/8" |
| Height to top of the standoffs |
44-3/4" |
| Height to top of the fireboard nailing flange |
48-1/4" |
| Depth of the body |
18-5/8" |
| Overall depth |
20-1/8" |
| Vent center from the back |
9-1/4" |
Letters match the drawings above.
Framing
| Opening width (A) |
86-1/4" |
| Opening height (C) |
48-1/2" |
| Depth (B) |
19-1/2" (18-1/2" for a see-through installation) |
| Base of the fireplace to the ceiling, minimum (E) |
84" |
Framing with the HeatFlo kit
| Register opening width (G) |
78" |
| Register opening height (H) |
7-1/2" |
| Framed register opening to the ceiling, minimum (F) |
3" |
| Recessed wall pocket, maximum depth |
3-1/2" |
Framing is 2x4 or larger. The opening width, height and depth stay the same with the HeatFlo kit. Corner framing dimensions are in the installation manual.
Installation Requirements
-
Clearances to combustibles: 1" to the outer wrapper at the back and sides, 0" at the side spacers, 0" at the top of the fireboard nailing flange and 0" at the floor. Don't pack insulation or other material around the fireplace.
-
Ceiling and enclosure: at least 84" from the bottom of the fireplace to the ceiling, and an 84" enclosure height.
-
Header: a header can sit on top of the fireboard nailing flange, which keeps it 11" above the fireplace top, but it can't be supported by the fireplace.
-
Front: keep 36" clear in front of the glass.
-
Side walls: a combustible side wall 14" or more from the fireplace opening can run any length; at 8-1/4" it can project up to 12". Combustible mantel legs must stay within the 45 degree safe zone shown in the manual.
-
Mantel: a 12" deep combustible mantel needs to be at least 12" above the fireplace opening; shallower mantels can sit lower, per the mantel chart in the manual.
-
Fireboard and finish: the 1/2" non-combustible fireboard that ships with the fireplace must be installed and can't be replaced or covered with drywall or other combustible material. Tile and other non-combustible facing can go over it.
-
TV above: Superior suggests mounting a TV at least 12" above the fireplace opening on a flush wall, or 18" in a recessed wall pocket with the HeatFlo kit, and the TV must stay within its maker's temperature rating.
-
Floor: on carpet, vinyl or any combustible floor other than wood, set the fireplace on a metal or wood panel the full width and depth of the unit.
-
Venting: use Superior 6DVL (DV Lock) 6" x 9" direct vent pipe. Start with at least 2 ft of vertical vent off the fireplace before any offset, and stay within 40 ft of vertical rise and the horizontal runs in the vent chart. Up to two 4 ft sections of 6DVL flex can be used, but flex can't pass through a ceiling, attic or wall. Keep 3" of clearance above horizontal vent runs and 1" at the sides and bottom, and 1" around vertical runs.
-
Power vent: for runs that natural draft venting can't handle, such as down-and-out installations, Superior's power vent kit uses Secure Vent rigid or Secure Flex pipe with a horizontal termination and the 6DVL to SV4.5 adapter.
-
See-through: the see-through conversion kit includes its own fireboard and framing changes. The factory blower can't be used in a see-through installation.
-
Gas: inlet pressure must be 5" to 10.5" WC on natural gas or 11" to 13" WC on propane. Propane needs the conversion kit.
-
Power: run a 3-wire, 120 VAC unswitched supply to the junction box on the left side of the fireplace. The batteries are backup only, and the blower and lights don't run on battery.
-
Altitude: the standard orifices cover 0 to 4,500 ft. Above that, the input has to be reduced; ask your gas supplier.
-
Massachusetts: installation and repair must be done by a licensed plumber or gas fitter. The flexible gas connector can't be longer than 36", and the shutoff must be a T-handle valve. A horizontal termination less than 7 ft above grade also needs a hard-wired carbon monoxide detector with battery backup on the floor where the fireplace is, and a GAS VENT DIRECTLY BELOW sign outside.
-
Manufactured homes: ground the fireplace to the chassis and don't cut or weaken the cross members. It must run on the gas shown on its rating plate unless a certified conversion kit is used.
-
Installation: must be installed by a qualified installer following the installation manual and local codes. Have the fireplace and venting inspected once a year by a qualified service person.
Frequently Asked Questions
What does the DRL6072 remote control?
The included hand-held remote turns the fireplace on and off, runs it in thermostat mode, and sets the flame height, blower speed and floor lighting, each with six settings. It also switches the pilot between IPI and CPI.
Is it available for propane?
It ships for natural gas. Superior's GCK-SM-6072NP conversion kit changes it to propane, at 43,000 Btu/hr high and 32,250 Btu/hr low.
Can it be a see-through fireplace?
Yes. The see-through conversion kit makes it two-sided, and it comes with the fireboard and instructions for that setup. The factory blower can't be used in a see-through installation.
Can I put a TV above it?
Superior suggests at least 12" from the fireplace opening to the TV on a flush wall, or 18" with a recessed wall pocket, and the TV must stay within its maker's temperature rating. The HeatFlo kit sends warm air out a register near the ceiling instead of up the wall, with no blower or power. Our guide to fireplace heat management explains how these kits work.
Will it work during a power outage?
Yes. Four AA batteries run the ignition and burner when the power is out. The blower and floor lighting won't run until power returns.
Can it vent down and out?
Yes, with Superior's power vent kit (PVK-PF2-SV4.5) and the 6DVL4.5PVA adapter. It uses Secure Vent rigid or Secure Flex pipe with a horizontal termination for layouts that natural draft venting can't handle.
What's the difference between the DRL6072 and the DRL4072?
They share the same 72" size, framing and Btu range. The DRL4072 leaves out the blower, floor lighting, porcelain liner and remote, comes with reflective black glass and a black painted interior, and needs a wall switch, thermostat or remote added.
Can it go in a bedroom?
Yes. The DRL6072 is listed for bedrooms, aftermarket mobile homes and permanently located manufactured homes, where local codes allow.
Warranty
Superior's 20 Year Limited Warranty covers the DRL6072 against defects in materials and workmanship:
- Fireplace body, firebox and barrier: 20 years
- Ceramic glass: 20 years, against thermal breakage only
- Burner, gas components and gaskets: 1 year
- Optional blowers and remote controls: 1 year
- Parts not listed: 90 days
- Labor: paid at IHP rates for the covered part's warranty period, up to five years
Vent components, trim and paint are not covered. The warranty is for the original owner of a fireplace installed in the US or Canada. Full terms are in the warranty certificate.
Documents and Downloads
