Empire 18" Fallen Timber Burncrete Log Set
The Empire 18" Fallen Timber log set (model number LS18CT) is a set of Burncrete gas logs for Empire's 18" slope glaze burners: the vent-free VFSR, VFSV, VFSE and VFSM, or the vented VSR. This listing is the logs only; an 18" slope glaze burner is required and ordered separately.
Empire log sets for slope glaze burners comply with ANSI Z21.11.2 for unvented heaters and ANSI Z21.60 for vented decorative appliances, so the set can run vent-free or vented, depending on the burner you choose and your local codes.
Key Features
- Burncrete gas logs
- Made for Empire 18" slope glaze burners (VFSR, VFSV, VFSE, VFSM and the vented VSR)
- Logs only; burner ordered separately
- Vent-free or vented use, depending on the burner and local codes
- Logs pin onto the burner in set positions
What to Order With It
This listing is the log set only. The slope glaze burners come with the rock wool embers and lava rock.
Required – Burner (choose one 18" Empire slope glaze burner):
-
Slope Glaze Burner, 18", Millivolt, Natural Gas (VFSR18NAT)
-
Slope Glaze Burner, 18", Millivolt, Propane (VFSR18LP)
-
Slope Glaze Burner, 18", Variable Flame Remote, Natural Gas (VFSV18NAT)
-
Slope Glaze Burner, 18", Variable Flame Remote, Propane (VFSV18LP)
-
Slope Glaze Burner, 18", Intermittent Pilot, Natural Gas (VFSE18N)
-
Slope Glaze Burner, 18", Intermittent Pilot, Propane (VFSE18P)
-
Slope Glaze Burner, 18", Manual, Natural Gas (VFSM18NAT)
-
Slope Glaze Burner, 18", Manual, Propane (VFSM18LP)
-
Vented Slope Glaze Burner, 18", Millivolt, Natural Gas (vented use only) (VSR18NAT)
-
Vented Slope Glaze Burner, 18", Millivolt, Propane (vented use only) (VSR18LP)
Optional – Embers, grate, riser and hood:
Specifications
| Model numbers |
LS18CT |
| Size |
18" |
| Material |
Burncrete |
| Burner |
Empire 18" slope glaze burner, ordered separately (VFSR millivolt, VFSV variable remote, VFSE intermittent pilot or VFSM manual; or the VSR vented millivolt burner) |
| Certification |
ANSI Z21.11.2 (unvented heaters) and ANSI Z21.60 (vented decorative appliances), per the log set manual |
| Minimum firebox |
Set by the burner: 28" front width, 17" rear width, 14" deep, 17" high for VFSR, VFSV and VFSE; 32" front width, 21" rear width, 14" deep, 17" high for VFSM; 28" front width, 15" deep, 22" high for the vented VSR |
Installation Requirements
-
Log placement: each log pins onto the burner in the position shown in the log set manual. Logs that do not sit firmly, or that are misformed or have loose pin holes, must be replaced.
-
Embers and lava rock: rock wool embers go on the front portion of the burner only; decorative lava rock goes on the firebox floor only, never on the burner.
-
Glass doors: keep any glass doors fully open while the fire is burning.
-
Soot: a properly installed set does not soot; if soot appears on a log, stop using it and call for service.
-
Codes: some state or local codes allow log sets only in a vented configuration; check yours. Vent-free installs must meet the burner's room size and bedroom/bathroom rules.
-
Installation: must be installed by a qualified installer per the burner and log set manuals and local codes. In Massachusetts the installation must be done by a licensed plumber or gas fitter.
Downloads
Warranty
The log set manual does not list warranty terms. Empire's vent-free log sets brochure refers buyers to empirehearth.com/warranty for current terms.
